Love of Muzzle Loaders

Monday, August 4, 2014

Correvon type Action

A rough mockup of a Correvon type action.
The (Google'd) original:

Cut from 1/4 inch thick plate steel.
Mounted on Walnut with 1/8 inch pins for a mockup. This would be the half-cock position or safe position.
Hammer head shape is not yet defined.

This position (full-cock) would be just before firing as the hammer slips past the trigger/sear. The trigger ring will be reduced in outer size, just for looks. Trigger ID is 1 inch diameter.

This would be the fired position not much different than half-cock.

Here is the coil spring (screen door type). 8-32 screw in rear, notched 3/32 inch roll pin in hammer.

Question: Will it pop caps?

Serial Number is "P" + "date".

Cherry wood, 1:28 .50 cal barrel piece.

Aug/13/2014
Start to inlet the .50 cal barrel.
Drill & Tap 5/8 inch x 18 US.

How it looks today.

Aug 17, 2014
Popped a cap.
Needs the front barrel band.

With brass band, heat blued hammer & trigger, brass pinned action.

Aug/21/2014
30gr FFFg - 777, .490 RB, Blue Tick Patch lubed with Bore Butter, 10 yards, No Sights on pistol.

Front Site Added: Brass Turtle.

Here is a link to the PDF of the action:
Correvon PDF

IdeZilla

Comments appreciated.

Monday, April 14, 2014

Boot Pistol Holster

I picked up a small piece of 6-7 oz leather at the Tandy store in Phoenix. Here are some pictures of an attempt to make a holster for the #3 boot pistol.

Not decided what to do with the small blank area of the back strap showing. Maybe some more designs there along with my initials and date. Top strap has a snap and rivet, lower strap is only riveted.

A Nicer Holster, 8-9oz leather, Charcoal Black ECO-FLO dye, 1/2 inch roller buckle. Room for half-cocked hammer.

IdeZilla

Comments appreciated.

Wednesday, April 2, 2014

Three Boot Pistols, .31 caliber

Here are a couple of really crude boot pistols. Both use pieces of a single Enfield DP .303 barrel.

Pistol #2
This one is the second of this series, it came out a bit better than the first one.
The barrel takes a .310 round ball without a patch. I have found some .315 round balls at Cabela's.

Yup, it is a bit small. Frame is 1/2 inch square tubing. Barrel is the last piece, the front. Lock is patterned after a very popular lock style. Nipple is a bit tall and may get replaced with a revolver type of nipple.

Left side of #2.
Cherry Stock, unfinished. No sights, yet. Trigger surface has been polished for a nice pull.

Left side of the lock. No half-cock, yet. Shows the trigger spring which is captive by short holes in the trigger and frame. Hammer head is left large until the barrel is attached. The hammer head will soon be shrunk and the tail may get curled up. A 6-32 button head screw holds the hammer spring to the frame. Hammer and trigger are from 3/16 inch thick stock.

Rear, angled view of the right side.

Added: Front sight, other part of that 5cents, LIBERTY * 1964

Added: Flash cup on hammer, .308 win brass.

APR/04/2014
New Walnut Grip.

Range Report 4/4/2014
.310 round ball, 30gr of 777 FFFg,
no patch, 11 meters. No rear sight.
At least it hit the target!

Pistol #1

Walnut burl for the grip. Longer barrel, the middle piece, still .303 Enfield.

Lock, with hammer cup, 10mm Brass.

5cents, 1964, Nose & Chin.

At rest.

Half cock.

Full cock.

Added: Brass face to the trigger, rear sight.
Barrel now riveted with 3/16 inch rod.

Added: #3 in a "family" shot.
It is a .40 cal smooth bore. Barrel is a Carcano piece drilled to .395 inches. Ramrod has .223 brass case as a tip.
Grip is Walnut Burl.

Range Report from May/07/2014
11M, .375 RB, 15gr of 777 FFFg, Red Ticking Patch lubed with Bore Butter.
Since there is no rear sight, it hit a bit to the right, need to fix that.

IdeZilla

Comments appreciated.

Thursday, February 13, 2014

Rear Sight Changed

Feb/13/2014
The rear sight has been changed to this newer one.

The old sight was removed from the top brass strip and replaced with this one. This sight is a bit fragile and this pistol will need it's own storage case for protection.

Each 1/4 turn of the thumb nut moves the sight tube up or down 0.0078125 inch.

Close up from the left side.
Base was modified to allow further downward movement (notched) to simulate the older sight tube. The base was then soft soldered to the top strip.

Right side view.

Top view.
The screw slot on the left is oval to allow for windage adjustments.

How it looks to the shooter.
Everything is in alignment vertically but the may not be.(Maybe it is now)

What you cannot see is that the top brass strip is adjustable for windage. There is a small "notch" that matches at the back of the frame and brass piece.

IdeZilla

Comments are welcomed.

Tuesday, February 11, 2014

Prototype Rear Sights

I started playing with some pieces of brass tubing and 22MAG brass.
I came up with this rear type of sight with elevation only.
Brass tubing attached to the base with a 6-32 US thread screw in the center.
A spring surrounds that base tube and pushes up on the slider tube.
The slider can move up or down about 1/4 inch.
The thumb nut pushes the slider down against the spring, hopefully holding it in place.
The loop keeps the 22MAG peep tube pointing forward.

Left Side, Full Up Position.

Left Side, Full Down Position

Left Rear, Full Down Position

Left Rear, Full Up Position

Rear View, through the 22MAG case, as a rear peep sight.

Pulling down on the slider spring shows the inner base tube.

IdeZilla

Reminds me of Steam Punk stuff.

Feb/12/2014
Here is another one, this is fun.
This sight has been designed to fit at the rear of "Underhammer Pistol, in progress".

Rear View.
It needs a lot of cleaning and polishing, it is rough.
Slider is positioned a bit higher, near the top of movement.

Here are the pieces.

Sight tube is a 22MAG brass that was picked up at the shooting range. Screw is 6-32 US thread.
Slider tube is larger than base tube. Base tube and slider tubes are soldered with low temperature silver plumbers solder, the rest with soft solder. Spring came from an assortment box from the hardware store.

The reason for the curly sight tube arm is for small bending amounts to align this sight tube to the front sight.