Lock of the Cherry Stocked Muzzle Loader

Here's some pictures of the unfinished lock.

It needs the left side plate and hammer stop block.
Sear spring fits around the trigger but not touching significantly.

Lock shown at half-cock.

 There is no trigger spring, yet.




 Full-cock below.

Side Plate is 1/8 inch thick, rear spring block is 1/4 inch thick and the two are riveted together. 8-32 tap for the hammer spring mounting screw. Spring is cut and made from an old handsaw blade. Sear is made from an old pair of worn out slip joint pliers, probably older than me. Sear spring fits into a hole in the hammer spring block and is music wire 0.040 inch diameter. There is a slight notch across the top of the sear to help keep the spring centered.

Hammer at rest or "just touching the nipple".

IdeZilla

Post comments if you would like more information, please.

Cherry Stocked Muzzle Loader

This is the beginnings of a .45 caliber, 1:28 twist, rifle project.

Some of these pictures would not fit into the cameras view so they are in pieces. Me standing on a chair to take pictures.

Here is what it looks like today.
Stock: Cherry
Barrel: Knight DISC remnant, purchased online from Green Mountain Barrels, internet specials. Needs tang.
Plug: 5/8-18 US thread, 6-line bolt.
Action: Underhammer, not done, full cock shown. Hammer spring not finished, spring needs trimming.

Right side of action panel.
Hammer and trigger. Trigger was cut out straight, hammered to make it wider, curled over vise screw.
None of these pieces are finished, just roughed out. Trigger spring visible.

Barrel came with a broken tap piece which was removed. I think this barrel is stainless steel, not sure.

IdeZilla


Please leave comments if you choose, thanks.

Front Brass Cap

Not much to report today, but a flat brass cap was added to the front of the stock. Changed brass screw types to slotted, seems to look better. Also, more of that applied mustard patterning is visible.

Last shot.

Some minor repairs to the rear sight as it shot to the left a bit and a ring was added to the rear sight.

The inside of the stock around the nipple needs bedding to keep the burning gasses from moving up between the stock and barrel, a pain to clean out each time.

IdeZilla

A Request, A Recycled Lock, more pictures added 10/10

Here are three older pictures of a lock. The hammer spring shown here was originally for a rifle.

Notice in previous posts that there is a new hammer spring and is now shaped for pistol finger clearance.
(See below, more pictures added)

The two 8-32 threaded upper holes in the back frame are for the longer flat head screws to mount this action into the stock. Trigger spring is "music wire" and is held in place by that notch/groove in the spring block and the right angle bend where it enters a hole in the trigger. The notches in the hammer are half and full cock notches. The half notch has been moved upward about 1/16 inch to enable the hammer head to be a bit closer to the nipple. Trigger and hammer have been hack sawed out of flat stock and several HF files have been worn out making these locks. This one is the easiest to make and get to work correctly. Note that the trigger pin axle is forward of the trigger sear ledge. This keeps the trigger and hammer locked together.

Also note that (in newer pictures) the action frame has been reshaped (greatly trimmed down) across the top. The rear spring mounting block has been riveted to the back frame piece using nails (about 1/8 inch diameter or so).

Here is another old picture with the side plate screwed down. 8-32 stock mounting screws are in the background.

Other side of the action. Shows the stock mounting holes.

 A mockup of what the lock looks like outside the stock.

A closer look

IdeZilla

Range Report, Oct 9

Here is that target, sitting as it was hanging at the range.  Started shooting at the center of the page, just to see what is going on.  All of the paper target hits were me getting used to how it shoots and trying to find out where it hits with the current sight settings.  Slowly changing rear sight elevation upwards as the pistol was shooting too low.

Then the orange target was used.
Last two hits are in the orange diamond's center, next to each other, left then right.

Looks like it's a shooter and not a safe queen.

The grip could be slightly modified smaller as its still a bit big.
It needs a loading stand.

IdeZilla
https://sites.google.com/site/onlyonsaturdaynight/

Добро пожаловать
Прошу
Witaj
Vítej
dobrodošli
ยินดีต้อนรับ
 Benvenuti
환영 합니다

Grip Changed.

IdeZilla
Comments Desired

Changed the grip

The grip shape was not working, to difficult to hold steadily. Wood was added to the back and reshaped. This grip shape is much easier to hang on to and my trigger finger does not support this pistol.

Then some mustard was applied on the barrel to obtain random patterns in the metal.
It is faint in this picture but definitely has a nice random pattern. If it wears off, there's more mustard in the fridge.

IdeZilla

Rear Sight, cleaned up.

Here is that rear sight cleaned up a bit

There is now a slight dovetail on the right edge of that elevator. Just enough to keep the elevator from wobbling.

You may notice that all of these rear sight pieces are soldered together, even the base elevator guides.













The stock is now sporting it's first coat of finish.
















Now off to the range!


















More Pictures:
http://idezilla.blogspot.com/2014/02/brass-rear-sight-up-close.html

IdeZilla

Rear Sight added

A elevation type of rear sight has been attached. It is crude and needs cleaning up, but at 100ft (or so) it is sighted in. Final shaping will take place as it gets used. The thumb nut stud will be clipped off. The brass base is soldered to the tang, can be removed if needs be. The elevator is held in place with the brass thumb nut. A piece of hexagonal tube was soldered on and sighted in for windage.

Here is a side view.

And another left side view showing the single calibration scratch.

The right side lifts outward ever so slightly when the thumb nut is tightened. For this one, the brass elevator can be upset and a tiny dovetail could be added to the base.

Off angle front view.

IdeZilla

More on "Just Another"

Today, this much was accomplished.
Barrel is now tanged, screwed in and pinned.
Grip shaping starting to appear.
Action mounted.
The front sight is on backwards, you say? Easily fixed, turn it around or just make another.

Action has had some work done, lowering the half-cock position (shown).
Stock shape is still not finalized. It may just get tapered back to front with enough left for a ramrod.
Not sure what to do with that slight hump at the rear.

Here is a fuzzy picture of the tang. Two 8-32 screws hold the tang to the plug while the brass screw holds the tang to the stock. Front edges of the tang have been shaped to match the barrel contour.

Looking for adjustable rear sight ideas.

I just hope that all of this work pays off with a shoot-able pistol.

The hammer spring has been tapered (width) being narrower at front and wider at the trigger. This keeps the hammer spring from intruding into the knuckle or grip area.

IdeZilla